Getting The Pool Ready For Winter

The information you are about to read is from years of experience. If you follow this procedure, you will get a safe and worry free closing, pool.

The first thing you want is to test the water and ensure that all levels including pH are normal. Next, go to want to shock your pool, and then run the filter for 24 hours. Now it's time to close the pool, clean the leaves or debris and vacuum your pool thoroughly. Now they want to pour the contents of yourConnection kit.

The next step will be to shut down the lines or the water in the tubes could be evacuated. You can do this without emptying pool. You need either a shop-Vac or a compressor. With a compressor you'll take an old winter plugs and remove the screw and push down the center, a compressor hose male adapter cm in the middle of winter draft. A thorn # 9 is more efficient. Now you can do it in one of the tubes on the filter. The first way to blow out linesLet all the plugs in the filter and pump, set the multi-port valve on the filter, and close all the plumbing line valves except the line you want to blow out. Open for the winter the air vent on the filter and press the cap with the compressor line and pump air into the filter. Thus, the water move the filter and push the water from the tap. Once you see the bubbles to install the plug winter, do this for the skimmer and returns. Open only the most importantDrain valve air force in the tube until you see air bubbles. Then close the valve once the air is kept in line and prevent water, prevent them from a. If you throw a step back just open the vents, remove the plug and equipment jet. Then open the valve of the jet filter, then force the air is all the water out of his mouth to stop the water is removed from the compressor, close the vents and you're done, now blowing the lines of thrust. Checkall plugs for air bubbles.

Now you need to remove to remove the plug in the pump winter at the bottom of the filter. If you have a chlorinator, you must remove the plug or remove the chlorinator itself. Absolutely sure that you shake that water can not be trapped in the chlorinator. Set the multi-port valve between any two of this selection, the valve is open and to avoid damage to keep at home.

Do not cover the pump for the winter. It is important thatthe pump will be able to breathe, you do not want to oxidize the interior of the pump. If you have a heater make sure the gas, turn the gas valve and remove the plug winter under the collector. It 'a good idea to cover the heater. Heating covers are in our online catalog. This will prevent getting acorns and other debris on the inside of the heater, and possibly cause a fire when it starts.

If you decide to use a vacuum to the lines of health, the easiest way to freeto do that your self a couple of pieces of Schedule 40 PVC pipe would get to count how many you have and how many 1 1 / 2 "Road 90A you need is. count how many skimmers you have, how many 1 1 / 2" male is your need is. For the skimmers measure how many inches is it from the bottom of the skimmer to the top of the water and add 2 ". Cut a piece of PVC on the measurement, the male adapter glue for PVC, wrap the threads with Teflon tape and screwAll aspire to the end of the skimmer. You can also use our Blow Out gizmo. Use Teflon tape on threads. To be able to turn off the skimmer, and act as a diaphragm to prevent the skimmer from cracking when it freezes. Now measure the holes back up the water and add 2 inches. Cut the PVC glue on that length of road 90A wrap the threads in Teflon tape and screw in the back, make sure the tube protruded from the water. Now you canwinter plumbing, all the valves to go to these accessories, turn on the vacuum and suck the water and lines. After the water from the pipes used in a number eight Winter connect the PVC and tighten.

Open made the capture of the suction pump in the hole you open the main valve exhaust. Reverse the vacuum and the air in this line. You can not see the air coming out of the main channel, but give up 30 seconds, and then close the valves. This will push the waterbelow the freezing level and prevent freezing. (Note: some of concrete above ground swimming pools may need to be evacuated or blown by a compressor). If you have a problem, the removal of plugs or you notice places were water can end up with, you should buy our any freeze. Just for this anywhere there may be a problem. If you use the PVC the skimmer, you should get a bottle of neighborhood, like an empty bottle of anti-algae. Fill halfway with small stones install the cap upside down and putin the skimmer. This will prevent the skimmer from cracking when it freezes.

To remove handrails and ladders, simply decorative cover, loosen the screw about half an inch up and then hammer down. This frees up your ladder or handrail. Then he pulls out of the cup. If you have a pool of vinyl, you can not empty the water below the skimmer to keep the level as in summer. This will prevent the liner, is decreasing in the corners and shortening the life ofliner. There is no reason to lower a vinyl pool. Vinyl is manufactured for guarantees on pools that could be reduced. If you have a cement pool, you must lower the pool, at least 1 foot below the skimmer. This is the link bar cracks causing tiles to fall to prevent and overcome. Now you're ready to put on the lid.

For water tube covers tires, fill in all the water pipes only three quarters of the way, install the cover and insert the tubes of water onCover the entire perimeter of the pool. Make sure there is enough water tubing that affect them. It is not advisable to put the water pipes in the cycle cover. Should cover the blow in the winter when the pipes for the coverage of these is the cover down, making it almost impossible to cover with the water pipes are new pull attached.

If you raise a protective cover to all the pieces of brass install the security problem, as usual. If there are any loose strapsThey should tighten.

For water tube covers Place the pump cover at the center of the lid and the pump every time it rains. Do not pump the cover, when the water is frozen, you will damage the pump. When you get to meet a safety and a vinyl pool, install a cover pump skimmer. Thus, water is pumped to avoid too much and allows easy access.

For concrete pools, it is important to maintain the water level below the tiles, when you take a stepCrush a pump cover on the second.

About the Author

See Review about easy pool at  Inflatable Above Ground Pools

And Easy Pool Shop at Lenxo.com